Commercial Garage Door Openers - Dallas Tx

LOGIC 4.O TECHNOLOGY (L4)
Added Value

• Built-in 3-channel, 315MHz radio receiver accepts up to 23 Security+® or unlimited DIP switch remotes. 3-button remotes can be programmed for OPEN/CLOSE/STOP operation
• Maintenance Alert System™ establishes a routine maintenance schedule based on the number of cycles or calendar date. Includes self-diagnostic system that allows you to troubleshoot up to eight different error codes
• Timer-to-Close allows programming in 1-sec or 15-sec increments and permits timed automatic door closure after the door reaches the full open position; requires monitored photo sensors, either CPS-U, CPS-UN4, or a 4-wire edge, using the CPS-EI edge interface
• Thermal motor overload can be easily reset from the 3-button floor level control station

 MEDIUM-DUTY LOGIC TECHNOLOGY

• UL325-2010 compliant Medium-Duty Logic programmable integrated circuit board
• Built-in 3-channel, 315MHz radio receiver accepts up to 20 Chamberlain® Security+® or unlimited DIP switch remotes.
  3-button remotes can be programmed for OPEN/CLOSE/STOP operation
• Programmable C2 or B2 wiring options (B2 requires CPS-U, CPS-UN4, or CPS-EI)
• Integrated Timer-to-Close (TTC) allows programming from 5 to 60 seconds in 5-second increments. Allows for timed automatic door closure after the door reaches the full open position (Requires monitored safety devices, with CPS-U, CPS-UN4, or CPS-EI)
• Integrated 90-second maximum run timer
• UL325-2010 Monitored Entrapment Capability
• Monitored protection against transient overvoltage conditions
• 3-button control station included

• UL325-2010 compliant Medium-Duty Logic programmable integrated circuit board
• Built-in 3-channel, 315MHz radio receiver accepts up to 20 Chamberlain® Security+® or unlimited DIP switch remotes.
  3-button remotes can be programmed for OPEN/CLOSE/STOP operation
• Programmable C2 or B2 wiring options (B2 requires CPS-U, CPS-UN4, or CPS-EI)
• Integrated Timer-to-Close (TTC) allows programming from 5 to 60 seconds in 5-second increments. Allows for timed automatic door closure after the door reaches the full open position (Requires monitored safety devices, with CPS-U, CPS-UN4, or CPS-EI)
• Integrated 90-second maximum run timer
• UL325-2010 Monitored Entrapment Capability
• Monitored protection against transient overvoltage conditions
• 3-button control station included

LOGIC 4.0 TECHNOLOGY (L4)
Added Value

• Built-in 3-channel, 315MHz radio receiver accepts up to 23 Security+® or unlimited DIP switch remotes. 3-button remotes can be programmed for OPEN/CLOSE/STOP operation
• Maintenance Alert System™ establishes a routine maintenance schedule based on the number of cycles or calendar date. Includes self-diagnostic system that allows you to troubleshoot up to eight different error codes
• Timer-to-Close allows programming in 1-sec or 15-sec increments and permits timed automatic door closure after the door reaches the full open position; requires monitored photo sensors, either CPS-U or CPS-UN4, or a 4-wire edge, using the CPS-EI edge interface
• Thermal motor overload can be easily reset from the 3-button floor level control station

 LOGIC 4.0 TECHNOLOGY (L4)
Added Value

• Built-in 3-channel, 315MHz radio receiver accepts up to 23 Security+® or unlimited DIP switch remotes. 3-button remotes can be programmed for OPEN/CLOSE/STOP operation
• Maintenance Alert System™ establishes a routine maintenance schedule based on the number of cycles or calendar date. Includes self-diagnostic system that allows you to troubleshoot up to eight different error codes
• Timer-to-Close allows programming in 1-sec or 15-sec increments and permits timed automatic door closure after the door reaches the full open position; requires monitored photo sensors, either CPS-U or CPS-UN4, or a 4-wire edge, using the CPS-EI edge interface
• Thermal motor overload can be easily reset from the 3-button floor level control station

MEDIUM-DUTY LOGIC TECHNOLOGY
Added Value

• UL325-2010 compliant Medium-Duty Logic programmable integrated circuit board
• Built-in 3-channel, 315MHz radio receiver accepts up to 20 Chamberlain® Security+® or unlimited DIP switch remotes. 3-button remotes can be programmed for OPEN/CLOSE/STOP operation
• Programmable C2 or B2 wiring options (B2 requires CPS-U, CPS-UN4, or CPS-EI)
• Integrated timer-to-close (TTC) allows programming from 5 to 60 seconds in 5-second increments. Allows for timed automatic door closure after the door reaches the full open position (Requires monitored safety devices, with CPS-U, CPS-UN4, or CPS-EI)
• Integrated 90-second maximum run timer
• UL325-2010 Monitored Entrapment capability
• Monitored protection against transient overvoltage conditions
• 3-button control station included

LOGIC 4.0 TECHNOLOGY (L4)
Added Value

• Built-in 3-channel, 315MHz radio receiver accepts up to 23 Security+® or unlimited DIP switch remotes. 3-button remotes can be programmed for OPEN/CLOSE/STOP operation
• Maintenance Alert System™ establishes a routine maintenance schedule based on the number of cycles or calendar date. Includes self-diagnostic system that allows you to troubleshoot up to eight different error codes
• Timer-to-Close allows programming in 1-sec or 15-sec increments and permits timed automatic door closure after the door reaches the full open position; requires monitored photo sensors, either CPS-U or CPS-UN4, or a 4-wire edge, using the CPS-EI edge interface
• Thermal motor overload can be easily reset from the 3-button floor level control station

 LOGIC 4.0 TECHNOLOGY (L4)
Added Value

• Built-in 3-channel, 315MHz radio receiver accepts up to 23 Security+® or unlimited DIP switch remotes. 3-button remotes can be programmed for OPEN/CLOSE/STOP operation
• Maintenance Alert System™ establishes a routine maintenance schedule based on the number of cycles or calendar date. Includes self-diagnostic system that allows you to troubleshoot up to eight different error codes
• Timer-to-Close allows programming in 1-sec or 15-sec increments and permits timed automatic door closure after the door reaches the full open position; requires monitored photo sensors, either CPS-U or CPS-UN4, or a 4-wire edge, using the CPS-EI edge interface
• Thermal motor overload can be easily reset from the 3-button floor level control station